騰達試驗儀器廠:
自動涂膜機是涂膜儀器,方便地在不同的底材上自動完成濕膜制備器或線棒涂布器的涂布運動,避免了涂膜過程中的人為因素誤差,能有效地提高制膜的重現性。
The automatic film coating machine is a coating film instrument,which can automatically complete the coating motion of the wet film preparation device or the wire rod applicator on different substrates,avoiding human error in the film coating process,and can effectively Improve film reproducibility.
自動涂膜機參數:
★涂布底座尺寸:475mm×350mm
★可真空尺寸;430mm×300mm
★可涂布長度:250mm或370mm
★涂布速率:0~10cm/s無**變速
★總功率:350W
★電源:220V 50Hz
★外形尺寸:705mm×505mm×270mm(長×寬×高)
★重量:約65Kg
AFA-II automatic coating machine parameters:
★Coated base size:475mm×350mm
Vacuum size available;430mm×300mm
★Coatable length:250mm or 370mm
★Coating rate:0~10cm/s without**
★Total power:350W
Power:220V 50Hz
★Dimensions:705mm×505mm×270mm(length×width×height)
★Weight:about 65Kg
自動涂膜機儀器特點:
★本設備采用無級變速電動機,**控制涂布速率。
★采用橫桿推動濕膜制備器,對濕膜制備器的外形尺寸無特殊要求。
★采用內置真空泵,方便本設備的攜帶及搬運。
★放置在涂布器底座的左側邊緣的不銹鋼廢料收集盤,可收集多余的涂料,以確保設備本身及周圍區域的清潔。
AFA-II automatic film coating machine instrument features:
★This equipment adopts stepless variable speed motor to control the coating rate.
★The crossbar is used to push the wet film maker,and there are no special requirements for the external dimensions of the wet film maker.
★Built-in vacuum pump is convenient for carrying and carrying this equipment.
★The stainless steel waste collection tray placed on the left edge of the applicator base can collect excess paint to ensure the equipment itself and the surrounding area are clean.
AFA-II自動涂膜機使用方法:
★接好電源。
★將待涂布底材(如:黑白紙)平放在涂布底座上,打開真空泵開關到“吸附”位置,這時,涂布底材即被吸附在涂布底座上了。(注意:當待涂布底材尺寸小于可真空尺寸時,應用其它紙張或用透明膠條遮蓋多余的真空小孔,以免待涂布底材吸附不牢固,造成涂布失敗)。
★將橫向推桿放置在涂布底座兩側的固定桿上。
★選擇適當的涂布長度,按下“復位”按鈕,使橫向推桿到達涂布的起始位置。
★將濕膜制備器放置在橫向推桿的前方。
★選擇適當的涂布速度。
★直接在濕膜制備器前面放置適量的待涂布涂料。
★按下“開始”按鈕,開始涂布。
★待涂布停止后,將剩余涂料刮入廢料收集盤。
★關閉真空泵,取下制好的樣板,以待下次操作。
AFA-II automatic coating machine use method:
★Connect the power.
★Lay the substrate to be coated(such as black and white paper)flat on the coating base and turn on the vacuum pump switch to the"adsorption"position.At this time,the coating substrate is adsorbed on the coating base.(Note:when the size of the substrate to be coated is smaller than the vacuum-capable size,use other paper or cover the excess vacuum holes with transparent tape to prevent the substrate to be coated from adsorbing weakly and causing coating failure)
★Place the horizontal push rods on the fixed rods on both sides of the coating base.
★Select the appropriate coating length and press the"Reset"button to make the horizontal pusher reach the starting position of coating.
★Place the wet film preparation device in front of the lateral push rod.
★Select the appropriate coating speed.
★Place an appropriate amount of coating material directly in front of the wet film maker.
★Press the"Start"button to start coating.
★After the coating stops,scrape the remaining paint into the waste collection tray.
★Turn off the vacuum pump and remove the prepared template for the next operation.
AFA-II自動涂膜機注意事項:
★在設備運轉過程中不能隨便調節涂布長度的旋鈕,否則會造成再次開機時滑桿不動作,一旦發生這種情況,可以把滑桿推到后,再開機,故障即可消除。
★涂布底座應保持清潔,有雜物粘在上面,以免影響涂布底座的平面度,從而影響下次涂布;若不慎將涂料滴落在涂布底座上,也應及時清潔。
★定時檢查油杯油位,若發現油位不夠,則應及時加入潤滑油,以潤滑導軌。
★每次使用本設備后,應用防塵罩遮蓋,以免灰塵掉入真空小孔,并被真空泵吸入,影響其使用壽命。
★每次使用本設備后,應及時清洗廢料收集盤。
Note of AFA-II automatic film coating machine:
★During the operation of the equipment,the knob of the coating length cannot be adjusted arbitrarily,otherwise the slider will not move when the machine is turned on again.Once this happens,you can push the slider to the machine and turn it on again,and the fault can be eliminated.
★The coating base should be kept clean,and there are debris stuck on it,so as not to affect the flatness of the coating base,which will affect the next coating;if the paint is accidentally dropped on the coating base,it should also be cleaned in time.
★Check the oil level of the oil cup regularly.If the oil level is not enough,add lubricating oil in time to lubricate the guide rail.
★After each use of the device,cover it with a dust cover to prevent dust from falling into the vacuum hole and being sucked in by the vacuum pump,affecting its service life.
★After each use of this equipment,the waste collection tray should be cleaned in time.
AFA-II自動涂膜機裝箱單:
A:主機1臺
B:附件.
1.橫向推桿1根
2.線棒夾具1根
3.廢料收集盤1只
4.說明書1本
5.產品合格證1份
AFA-II Automatic Coating Machine Packing List:
A:Host 1
B:Attachment.
1.One horizontal putter
2.Wire rod clamp 1
3.Waste collection tray 1
4.Manual 1
5.Product certificate